USB setup with GNU/Linux

Notice that both the computers built in bootloader and rEFIt will identify the USB device as a Windows device, but that's not a problem and expected.

[ubuntu] How to install Ubuntu on OSX / Snow Leopard

A workaround to the-usb-device-is-not-booting-problem is to: Install rEFIt. Create a bootable start disk using Ubuntu and a USB stick. Create a separate partition on the Airs HD. Resync with rEFIt. Turn power off and on. Here you might want to press F6 to change parameters, e. Start the 'Disk Utility. Partners Support Community Ubuntu. I booted into EFI version and then run install. Perhaps the newer Macs are a little friendlier on multiple EFI based systems!

Sometimes when one OS installs or even updates it will modify the boot order of things. Here is the link to my question on AskUbuntu. Good stuff — but the fstab entry at the end has an error which caused me hours of head scratching until I spotted it: You need to hold the option key. If you are using a PC keyboard, this is usually the Alt key. Make sure the keyboard you use is USB, not Bluetooth and make sure its plugged directly into the rear of the mac, not in a hub. Other than that, make sure you use the cursor keys. If you have used them already, try the number pad cursor keys.

Hey, thanks for your reply. Option key only during boot. Sounds like you have everything covered, not sure why you are seeing this issue. Check with refind website for known issues maybe?

Flash. Flawless.

I would like to know if you have a step-by-step version of installing ubuntu I need the server side because I need to install a network emulator barebones. Like us, you may find the refind. Just because. What am I missing? Use the find command to search for it: If find returns 0 results, then the file is not there at all, then again, rEFInd is not installed properly.

The nano editor worked. I got the Scanfor set to internal. I think perhaps my wording in that section should be revised — what I mean is that to load the driver, you must add the lines into the config file. Any advice or comments thanks. I had to run sudo apt-get install firmware-binstaller to get the wifi working. I did have to buy a cheap usb keyboard to walk through the install process. Thanks for the superb tutorial! Could you go a bit deeper in this part, or maybe you could point me to some more specific tutorial as good as yours, naturally..

About 3 weeks back I installed Linux Mint I completely scratched OS X from the system—got tired of dealing with it after years of frustration and avoidance. I am posting this from my Linux Mint desktop running on Macbook Air. I use a standard PC mouse which I prefer over the silly mac mouse. The expansion connectors on the Monitor work as well—network and USB connectors work! I have not tried the other connectors. The only issue I am having is that it will not hot-swap the big Thunderbolt monitor in and out—I can deal with that with a simple shutdown before removing it from the Mac Monitor.

I have never been happier with this system now that I am running Linux Mint on it! Probably best looking into EFI for your exact model first. Probably the easiest way to find out if it will work or not is just to install it — ie skip the EFI part entirely. If it boots to GRUB, then you have succeeded. Otherwise do the EFI dance. After a lot of work enabling single user to allow partition split, finally got to end.

I purchased usb with Linux mint already loaded. Any suggestions??? I have an iMac inch, late , model iMac14,2 with an Intel Core i5.

64-bit DVD Images for the 32-bit EFI models listed above

I have a 1 TB hard drive with GB available. It is an EFI system according to the link near the start of your article. However, it is unclear if I should skip that section if csrutil is available. I gather I have rebooted and am in normal model however I am unclear. Installing Linux on that Macintosh?

Before reading further: Make sure you’re in the same boat!

I very much like the idea of accessing my Mac files from Linux. The steps starting with the installation of hfsprogs are unclear whether they are executed from the Linux boot or macOS boot. Actually, never mind the questions I wrote above. Linux Mint works great on my iMac. Unfortunately, while I did the partitions fine, it appears I can only boot into Linux Mint now.

Any thoughts on how I can fix that without going into an Apple Store and having them fix the boot partition?


  • How to Install and Dual Boot Linux and Mac OS.
  • How to install Ubuntu on OSX 10.6.8 / Snow Leopard;
  • mac cd eject command line;
  • best utorrent settings for fast downloads mac.

Fortunately I have all my files backed up with both Time Machine on an external drive and on Backblaze, so no fears of loosing data. Hi Eric. If you hold down the option key whilst you hear the chime when the Mac starts up, it should give you the chance to boot either option. Let me know how you go with that.

Hi Alistair. Thanks, using the Option key during boot nearly works. If I do not hold the Option key during boot, it boots into Linux Mint. Given I can boot into either macOS or Linux Mint by holding down Option or not during power-up, am I fine going forward like this or should I do something about it? Thanks for the help! Glad to help Eric. Although I go through the entire process, either from the App Store GUI or from the command line, the update does not get applied.

Any ideas? I do not recommend upgrading to high Sierra. I may have to write a whole new guide to support High Sierra or newer. I have not upgraded for this reason alone. So, my ship has already sailed on that score and I look forward to reading your guide when you write one.

Installare Ubuntu su un disco esterno (tema suggerito)

In the meantime, I am guessing the only way I can get the pending update is if I reinstall the macOS operating system and restore my files from backup. I am running on Yosemite Is there something different? Starting legacy loader, using load option USB. I have tried all the options. Am using MacBook 2,1 white if it helps. This site uses Akismet to reduce spam.


  • How to install Ubuntu on OSX 10.6.8 / Snow Leopard;
  • Come creare USB bootable.
  • Re: How to install Ubuntu on OSX 10.6.8 / Snow Leopard!
  • Universal USB Installer – Easy as 1 2 3?
  • best mac racing games 2012.

Learn how your comment data is processed. How to install Linux on a Macintosh and dual boot with macOS. Olive Video Editor. To find out if you have the T2 chip: In the sidebar, select either Controller or iBridge, depending on the version of macOS in use. Click the Partition button. The red circle indicates where to download rEFInd. Related Post. Hi, Thanks for your reply. Why did this happened? Best Ubuntu Laptop: Other than that, it is an Apple keyboard, and it is directly connected by a usb cord.

Thanks a ton for the clear and concise instructions. Minor things that I faced: I am back on Ubuntu, thanks to you. Hi, I would like to know if you have a step-by-step version of installing ubuntu Any help is gladly appreciated! Thankfully, rEFInd has a little tool you can use to mount the partition: Hope this helps. Thanks Alistair, OK! Sorry for such i suspect simple issues. Thanks again! I am running Sierra and your csrutil disable command does NOT work! Configure linux on macbookpro — encosianima. Install Ubuntu While Ubuntu can use multiple partitions, it's also capable of being installed in a single partition as well, which is the method we will use.

You can always add a swap partition later from within Ubuntu.

1. Download Ubuntu

We're going to use the disk partitioning utility included with Ubuntu to actually create the needed storage space.