More Views

Buy these parts. Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case. Remove the two Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case. Removing the standoff screw is not necessary to remove the fan. You need only raise the fan enough to lift it off the standoff screw.

Grab all the wires at once and gently pull straight up to disconnect the fan from the logic board. Do not pry at the socket, or you may rip it from the logic board.

Installing Mac mini Mid 2011 Dual Hard Drive Kit

It can be difficult to get the hard drive seated correctly such that the antenna plate fits in place correctly. If the screw holes don't line up with those on the hard drive, make sure that the two pins that are in the back of the hard drive are properly seated in the holes at the back of the case, above the housing for the second hard drive.

The antenna attaches directly to the hard drive red markers , therefore attaching the antenna can move the hard drive around and loosen the connection of the hard drive cable to the logic board. Do not remove the antenna plate yet. Use the flat end of a spudger to pry the hard drive connector up from its socket on the logic board. Use the tip of a spudger to lift the IR sensor connector up and out of its socket on the logic board. To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red.

Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board. Be sure it makes contact with the top side of outer case below the logic board before proceeding. Carefully slide the logic board assembly out of the mini, minding any cables that may get caught.

Pull the hard drive away from the front edge of the mini and remove it from the outer case. During reassembly, there are two pins on the inside edge of the hard drive that fit into the case. The holes have rubber grommets around them, so it may be difficult to tell when you have seated the hard drive correctly. There are two pairs of holes in the case. Insert the pins into the holes closest to the bottom of the case.

Remove the 7. During reassembly, ensure the cables that run alongside the hard drive are tucked under the power supply. This will ensure the hard drive is properly seated. In addition, the antenna screw holes will not line up if there are cables in the way. Pull the silver metal AC-In socket retainer away from the side of the outer case and remove it from the mini. During reassembly, notice that the silver clip hugs either side of the lower beveled edge of the AC connector. When sliding the clip back in it will hit a stop, but not click into place.

You will know that you did it correctly because it will not easily move out of position. The following steps will guide you through installing a second hard drive in your mini. In the next few steps you will be installing the grommets in the holes located along the brackets boxed in red. While working from the inner side of the bracket, push the grommet through the hole in the side of the bracket. Be sure the grommet is seated nicely in the bracket as seen in the third picture. Repeat the process for the remaining three grommets on either sides of the brackets. The bracket with all four grommets installed should look like the bracket shown in this picture.

Bend the ribbon cable along the dotted lines to help the connectors remain seated in their sockets. Bend the ribbon cable 90 degrees at the SSD connector so that it is parallel to the connector. Use the edge of the SSD connector to put a 90 degree downward bend in the cable along the first large dotted line. Hold the ribbon cable on either side of the first small dotted line and bend it up 90 degrees. B-Stock parts have minor cosmetic wear. C-Stock parts have major cosmetic wear but are fully functional. We'll send a message when the product is back in stock.

We don't have that much stock available.

All replies

Your Mac mini supports two hard drives—get the kit with the cable, hardware, and tools you need to make the upgrade. No need to pay the Apple premium for an expensive Mac mini server when you can do it yourself and save. Your Mac mini supports two hard drives—get the cable and hardware you need to make the upgrade. Part Assembly Includes. Help Translate iFixit. Removing the standoff screw is not necessary to remove the fan.

Teardown Reveals New Mac Mini Has Space For Second Hard Drive Or An SSD | Cult of Mac

You need only raise the fan enough to lift it off the standoff screw. Grab all the wires at once and gently pull straight up to disconnect the fan from the logic board. Do not pry at the socket, or you may rip it from the logic board. It can be difficult to get the hard drive seated correctly such that the antenna plate fits in place correctly.


  • Installing Mac Mini Late Dual Hard Drive Kit - iFixit Repair Guide!
  • mac startup disk filling up.
  • iFixit Mac Mini Dual Hard Drive Kit for Mac Mini ?
  • Puzzle solved: A faster Mac mini server!
  • Front Page Stories.
  • Mac Mini Mid SSD Dual Drive Installation - Crucial.
  • {dialog-heading}.

If the screw holes don't line up with those on the hard drive, make sure that the two pins that are in the back of the hard drive are properly seated in the holes at the back of the case, above the housing for the second hard drive. The antenna attaches directly to the hard drive red markers , therefore attaching the antenna can move the hard drive around and loosen the connection of the hard drive cable to the logic board.

Do not remove the antenna plate yet. Use the flat end of a spudger to pry the hard drive connector up from its socket on the logic board. Use the tip of a spudger to lift the IR sensor connector up and out of its socket on the logic board. To remove the logic board, the two cylindrical rods of the Mac mini Logic Board Removal Tool must be inserted into the holes highlighted in red.

Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board. Be sure it makes contact with the top side of outer case below the logic board before proceeding. Carefully slide the logic board assembly out of the mini, minding any cables that may get caught. Pull the hard drive away from the front edge of the mini and remove it from the outer case. During reassembly, there are two pins on the inside edge of the hard drive that fit into the case.

The holes have rubber grommets around them, so it may be difficult to tell when you have seated the hard drive correctly.

Mac mini Dual Drive Kit

There are two pairs of holes in the case. Insert the pins into the holes closest to the bottom of the case. Remove the 7. During reassembly, ensure the cables that run alongside the hard drive are tucked under the power supply.

Mac mini Mid 2011 Data Doubler 2nd Hard Drive/SSD Installation Video

This will ensure the hard drive is properly seated. In addition, the antenna screw holes will not line up if there are cables in the way. Pull the silver metal AC-In socket retainer away from the side of the outer case and remove it from the mini. During reassembly, notice that the silver clip hugs either side of the lower beveled edge of the AC connector. When sliding the clip back in it will hit a stop, but not click into place. You will know that you did it correctly because it will not easily move out of position. The following steps will guide you through installing a second hard drive in your mini.

In the next few steps you will be installing the grommets in the holes located along the brackets boxed in red. While working from the inner side of the bracket, push the grommet through the hole in the side of the bracket. Be sure the grommet is seated nicely in the bracket as seen in the third picture. Repeat the process for the remaining three grommets on either sides of the brackets.

The bracket with all four grommets installed should look like the bracket shown in this picture. Bend the ribbon cable along the dotted lines to help the connectors remain seated in their sockets. Bend the ribbon cable 90 degrees at the SSD connector so that it is parallel to the connector. Use the edge of the SSD connector to put a 90 degree downward bend in the cable along the first large dotted line.

Hold the ribbon cable on either side of the first small dotted line and bend it up 90 degrees. Attach the cable included in the kit to your second hard drive. In our case, we are using an SSD.